Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
Almost everyone may have their own assumption about Tools You Need to Install a New Bathtub .
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Setting up a bath tub isn't precisely rocket science, however it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is easily accessible, the project can move immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will require an assistant to leave the old tub and also set in the new one. Make certain you have qualified on your own for the work and also fit trying it. Rather than hiring a specialist to take over a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly help you mount a brand-new bathtub in your restroom if you have actually currently bought a brand-new tub and also don't require to change the plan of your previous supply of water pipelines.
Your tools and also material checklist need to comprise the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is detach the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be quite problematic due to the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the staying water that will certainly come from the pipes. When the supply pipelines have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous type must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of both wooden boards under its feet, put the bath tub in the required placement. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub until the level reads level.
To mount taps, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Turn on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as also check the overflow outlet as well as the typical outlet for leaks.
Lastly, fix the bath paneling as explained in the producer's user's manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been used at the very least when as this will resolve it into its last setting.
Getting ready for the Installation
To start with, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid strain on the tub.
Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its final setting.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface in between the bath as well as the tiling, bring about difficulties with dampness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to allow for the movement experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently readily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that editorial on How to Install a Bathtub from someone on our other site. Do you know another individual who is enthusiastic about How to Install a Bathtub? Feel free to promote it. I take joy in reading our article about How to Install a Bathtub.
Stop the flood! Call. Report this page